Shraddha Impex

Features:

• Reliable
• Durable
• Good finish
• Fine quality

• For verifying and setting clockwise torque wrenches and torque screwdrivers in the range from 0.2 - 3150 N·m
• Simple, electronic torque tester with integrated torque transducer (DMS)
• With fixed hexagon female drive 1/4", 10, 17, 36, 46 mm or 1.1/2"square drive adapter (model dependent)
• With 1/4", 3/8", 1/2", 3/4", 1"square drive adapter or bit adapter (model dependent)
• High measurement accuracy: +/- 1 % tolerance of reading, +/- 1 digit
• Break-Point-measurement (1st peak)
• Auto reset
• Can be switched from N·m to lbf·ft
• Serial interface RS232
• Optionally available: adapter for cigarette lighter socket (12 V), no. 8612-390

• Freely set torque values within the capacity range. Replaceable socket, ratchet wrenches.

• The ratchet improves efficiency. These wrenches are well suited for repetitive work.
• By replacing the sockets, various sizes of fasteners can be tightened within the tool's capacity range. 
• By reversing the ratchet, the wrench can be used to loosen fasteners counter-clockwise.
• Tightening to a torque setting can only be done clockwise.

• Accuracy:+-3% of indicated value over the full range.

Additional Information:

• Item Code: N100QLK

• Controlled tightening and verification of tightening values
• For use in all areas of industrial manufacturing and in quality control
• Working ranges of 0.8 to 2000 N·m are covered Features:
• Dial-indicating torque wrench with dual scale and multi-functional slave pointer
• 1/4", 3/8", 1/2", 3/4"or 1"double-square drive with ball locking device
• With integrated ratchet-function for controlled bi-directional tightening
• For controlled screw tightening and torque measurements
• Working accuracy: +/- 4 % tolerance of the indicated torque
• Acc. to DIN EN ISO 6789, traceable to national standards
• With dual scale in N·m and lbf·in or lbf·ft double-tinted clearly readable face
• Integrated overload protection - mechanical stop up to max. 25 % overload of the maximum value
• Housing made of lightweight, robust special aluminium construction - lacquered, silver-grey
• Black, non-slip rubber handgrips
• 10 models in the range 0.8 - 2000 N·m
• Models 8301-04 to 8301-40: EPA-conformant (Electrostatic Protected Area), for use in sensitive electrostatic applications
• Audio-visual signal is standard on models 8303-40 to 8305-20 Scope of delivery:
• Dial-measuring torque wrench type 83
• Battery for models having audio-visual signal
• Test certificate acc. to DIN EN ISO 6789
• Delivered in a sturdy black plastic box (no. 8301-04 to 8302-20), otherwise in sturdy cardboard packaging (no. 8303-40 to 8305-20)

• The Torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
• Available in: lb-in, kg-cm and N-m
• Peak, Real Time and Peak Down measuring mode (selectable)
• 800 data memory.
• Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
• Programmable screw tightening counter
• Programmable Auto Zero function resets unit to zero for easy operation
• Both CW and CCW operation
• ASCII format output(USB)
• Runs on internal Ni-MH batteries (for 12 hours) Auto shut-off after 10 min. of non-use
• AC charger and carrying case included.

• Controlled screw tightening in the range 6 - 3000 N·m
• For use in almost all industrial manufacturing areas Features:
• Classified to DIN EN ISO 6789:2003 Type II Class A, with a factory certificate. Working accuracy: +/- 3 % tolerance of scale set torque. The specification of the standard(+/- 4 %) is exceeded.
• Automatic short-path actuation with tactile impulse and audible signal
• Dual scale (except for type E-F) with corresponding scale graduation (see table)
• Type B, BC, C with push-button release
• Type BCK with integrated ratchet function Technical advantage/Function:
• Lightweight and robust (as housing is made of an aluminium alloy), very workshop-friendly
• No inaccuracies whether used with both hands or held away from the handle (as for standard torque wrenches) Both the square drive and fulcrum are on an axis which ensures a high degree of user safety; can be extended to reduce the user's working load.
• Extremely low wear attributable to reduced forces in a unique lever mechanism
• Forged lever chain from our own quality forge
• Maximum precision even when subjected to extreme continuous use
• Long life cycles and tool lives
• Easy operation - fast and safe torque tightening
• Easy adjustment thanks to attractive adjusting button secured against loss at the end of the handle
• Single- and double-square drive for controlled bi-directional tightening

• Controlled screw tightening in the range 1 - 10 N·m
• Ideal for assembly work where controlled tightening with low torque values is required (e.g. electronic hardware sector, precision mechanics etc.) Features:
• Adjustable torque wrench - with scale
• 1/4"square drive with ball locking device
• With integrated ratchet-head function for controlled clockwise tightening
• Working accuracy: +/- 6 % tolerance of set torque
• Acc. to DIN EN ISO 6789, traceable to national standards
• Precision mechanism slips very noticeably and audibly ("click") when the set torque is reached - over-tightening is not possible
• Automatic resetting to the starting position
• Micrometer scale graduation: 0.05 N·m / 0.1 N·m
• 2 models in the range 1 N·m to 10 N·m
• Extremely lightweight yet robust and corrosion-resistant construction design
• Very convenient non-slip rubber handgrip
• EPA-conformant (Electrostatic Protected Area), for use in sensitive electrostatic applications Scope of delivery:
• Torque wrench type TSC SLIPPER
• Test certificate acc. to DIN EN ISO 6789
• Delivered in sturdy cardboard packaging